1956 Ford F100 Custom Cab 1/2-ton short bed
1956 Ford F100 Custom Cab 1/2-ton short bed - Image 11956 Ford F100 Custom Cab 1/2-ton short bed - Image 21956 Ford F100 Custom Cab 1/2-ton short bed - Image 31956 Ford F100 Custom Cab 1/2-ton short bed - Image 41956 Ford F100 Custom Cab 1/2-ton short bed - Image 5
Category :
Location : Allen Park, Michigan


1956 F100 Custom Cab…running project Dearborn Michigan area…about 2-miles from Ford World Headquarters…right near Greenfield Village! I must part with my F100 project... Bring a trailer and cash and it’s all yours... PLEASE...NO CALLS after 10 P.M. Detroit time! Selling as a package. Asking $10,000 or best offer...open to trades PLUS cash?... I have much more that this in the truck AND NEW parts! 1956 F100 --- Red with White top original 2-tone paint ALL ORIGINAL truck inside & out except for motor & transmission… 302 2-bbl AND C4 transmission pulled from a wrecked 1970 F100…PLUS extra C4, got it with the truck! Fiberglass front fenders…they where installed when I purchased the truck! PARTS LIST: NOT installed...ALL NEW in BOXES!!! 2nd set of original rear fenders with spare tire cut-out on driver side fender ---almost NO rust 1970 F100 9-INCH rear axle housing with all brackets removed & cleaned up Ford 9-inch Big (Torino) Bearing Rear Disc Brake Conversion kit... ...rotors are 5” x 4 ½” Ford pattern... Ford Racing Parts # M-4204-F28A, TRAC-LOC Limited Slip, with 1536-steel billet case caps. ALL bearings & gaskets needed to assemble rear pumpkin…. VISTEON 9" ring and pinion set. Ratio is 3:89. --- polished and de-burred. Ring gear has been back -cut! From a top NASCAR team in Mooresville, North Carolina…ONLY has ONE 400-mile race on it... New Dutchman 28-spline Street/Strip axles & retainers with bearings…NEED axle SEALS! Extra “hooded” Daytona pinion bearing support without races/bearings 1956 Running boards --- need a few repairs 2nd set of “short” cab-length running boards…I was going to use these to repair the long ones! Total Cost Involved Mustang II style Independent Front Suspension with tubular A-arms and air springs with sway bar…rotors are 5” x 4 ½” Ford pattern... No Limit Engineering FAT BAR 4-bar parallel rear suspension with air ride, includes panhard bar! Art Morrison Enterprises 2" x 4" square steel tubing for NOTCHES...”bent the hard way”... …SAME dimensions as the front & rear sections of the OEM frame rails…2” x 4” ...I was going to use these for a rear step-notch! Accuair Stage II management system with ride height sensors, key fobs, filter, EVERY option available!!!...best of the best! !... VIAIR 400C Dual Performance Value Pack compressors… same ones sold by Accuair!...no waiting with TWO compressors... 12-gallon 8-port D.O.T approved air tank for air ride system ALSO AVAILABLE! Probe Industries SPORTSMAN RACE SERIES Ford 331/347 Flat Top -4.0cc - SRS Piston Set ...And... Clevite - Perfect Circle Moly STREET / RACE Ring Set: Part #315-0049-030 1/16" - 1/16" - 3.0mm (std. oil ring) Early ‘60’s SMALL BLOCK FORD Buddy Barr/Holley TRI POWER set up!!!...all original...fuel log, oval air cleaner & a vintage MOON fuel block from the 60’s!…includes THREE rebuild kits from HOLLEY! VINTAGE 60’s MOON EQUIPPED TRI POWER FINNED ALUMINUM FUEL BLOCK VINTAGE Set of Small Block Ford Aluminum Cal Custom "Hawk" 9-Fin Valve Covers SOME TRUCK PICTURES HERE... http://s88.photobucket.com/albums/k200/rockher_man/1956%20F100%20PROJECT/ -